How to disable Low Ink Warning in The Hp Deskjet 2466

11:39 AM Posted by

A few days ago my printer Deskjet 2466 always show low ink warning and this message very disturbing my work. After searching the service for my HP printer that running  in my computer, I found 2 service running for this HP printer. I try to disable the service and it success remove warning message in my computer.

Besides tried in my computer this method on my computer that using HP deskjet 2466, I also tried on other computer that installed that using HP deskjet 2180 all in one printer and it working 100%. The both printer using cartridges HP21 and HP22. I thinks this methods also can be used to remove low ink message on other printer that using the same HP cartridge types.

Here the Methods to Disable Low Ink Warning in the HP Deskjet 2566:
  1. Open system configuration utility by click start-run then type msconfig
  2. Go to Startup Tab then disable HPWuSchd2 and HP Digital Imaging
  3. Click apply then Ok
  4. You must restart the computer to take effect
The above methods only for disable low ink warning, not reset the ink level. To reset ink level on the HP printer models mentioned above you use this methods: Ink Levels Reset for HP Cartridges HP21, HP27, HP56, HP58 and How to Reset Ink Levels for HP Cartridges HP22, HP28, HP57. Good luck.


Read More Add your Comment 1 comments


Repair or reset for HP Cartridges HP22, HP28, HP57

7:58 PM Posted by

Ink level Reset method for HP Cartridges HP22, HP28 and HP57 almost similar with Ink Levels Reset for HP Cartridges HP21, HP27, HP56 and HP58. HP22, HP28 and HP57 is color cartridges HP printers. This manual reset methode to solve low ink warning on this hp cartridges. This ink levels reset method has tested and also work on my HP printer HP D2466.  If this ink levels reset methode does not work on your HP printer, you can try more than 1 times in your hp printer.

Here Ink levels reset methode for HP Cartridges HP22, HP28 and HP57 (On most models):
  1. Remove cartridge from your printer.
  2. Place a piece of tape over the top left contact as shown in red on the picture to the right.
  3. With the tape covering the contact place cartridge back into printer.
  4. The printer will perform and alignment page. (Some newer models no longer print alignment pages. If printer runs through a series of priming routines and stops for 20 seconds continue through with next step)
  5. Once an alignment page has been printed remove cartridge from printer.
  6. Place a piece of tape over the second contact shown in red.
  7. Place cartridge into printer with both pieces of tape. (One covering the first contact and one cover the second contact.)
  8. Printer will print another alignment page. (Some newer models no longer print alignment pages. If printer runs through a series of priming routines and stops for 20 seconds continue through with next step.)
  9. Once the second alignment page has been printed remove cartridge from printer.
  10. Remove tape pieces from cartridge contacts
  11. Make sure there is no residual adhesive on cartridge contacts.
  12. Place cartridge into printer. Cartridge should now read full.
Notes: It is very important that there is no residual adhesive on the cartridge contact point. This will make reading the cartridge difficult.


Read More Add your Comment 28 comments


Repair or reset for HP Cartridges HP21, HP27, HP56, HP58

7:45 PM Posted by

This reset methods be used to reset ink levels on HP printer that using cartridges HP21, HP27, HP56 and HP58 (On most models). I have tested this reset methods on HP Deskjet 2466 and work perfectly but in other HP printer types  this reset methods does not work.

To do this reset methods no software resetter required, just require  only a piece of tape. If this reset method does not work on your printer you will need to repeat this process. If you have to reattempt the reset turn your computer off before doing so. Leave computer off during the reset process or disconnected the printer from computer.

Here the Ink levels reset methode for HP cartridges HP21, hp27, hp56 and HP58:
  1. Remove cartridge from your printer.
  2. Place a piece of tape over the top left contact as shown in red on the picture to the right.
  3. With the tape covering the contact place cartridge back into printer.
  4. The printer will perform and alignment page. (Some newer models no longer print alignment pages. If printer runs through a series of priming routines and stops for 20 seconds continue through with next step.)
  5. Once an alignment page has been printed remove cartridge from printer.
  6. Place a piece of tape over the second contact shown in red.
  7. Place cartridge into printer with both pieces of tape. (One covering the first contact and one cover the second contact.)
  8. Printer will print another alignment page. (Some newer models no longer print alignment pages. If printer runs through a series of priming routines and stops for 20 seconds continue through with next step.)
  9. Once the second alignment page has been printed remove cartridge from printer.
  10. Remove tape pieces from cartridge contacts Make sure there is no residual adhesive on cartridge contacts.
  11. Place cartridge into printer. Cartridge should now read full.

Additional Notes: As stated above it is very important that there is no residual adhesive on the cartridge contact point. This will make reading the cartridge difficult.


Read More Add your Comment 1 comments


Repair or reset Canon PIXMA MP240 printer

8:46 AM Posted by

How do you repair or reset Canon PIXMA MP240 printer after refilling ink cartridges? I refilled the Canon PIXMA MP240 cartridges using a refill kit. Printer won't recognize them anymore. Hours of Googling and pressing random buttons resulted in nothing useful. Any idea if it's even possible to "convince" a Canon PIXMA MP240 printer to take refilled cartridges? If so, how?

Repair or reset Canon PIXMA MP240 printer:
  1. Disconnect the power cable to the printer.
  2. Hold down the On/Off button.
  3. Reconnect thew power cable.
  4. With the power button still down, press the Stop/Reset button twice.
  5. Release the On/Off button.
  6. The printer is now in the factory mode (wait until idle is displayed)
  7. Press the right arrow button (next to the OK button) repeatedly until Shipping Mode 3 is displayed.
  8. Press the OK button.
  9. Wait until "Without Cleaning" is displayed and then press the Stop/Reset button once.
  10. A test page should print, but if not, don't worry.
  11. Open the cover. The cartridge should position themselves at the far left-(the cartridge removal location.)
  12. Disconnect the power cable.
  13. Remove both cartridges.
  14. Close the cover.
  15. Reconnect the power cable.
  16. Press the On/Off button.
  17. Wait until a Replace Cartridges message is displayed. Now insert the cartridges.
  18. Close cover and wait until the printer is in the normal mode and displays the normal start menu (i.e. Copy)


Read More Add your Comment 1 comments


Repair Blink HP Deskjet D2566, 2466, 3535, 3420, 3920

7:26 PM Posted by

Repair Blink HP Deskjet
HP Deskjet 2566 printer is a printer with the price is quite cheap and reliable. However, in my opinion, the ink storage capacity is smaller than previous versions, D2466 and other. Same with other printers, HP Deskjet D2566 printer, chances are, you will find a blink or flashing LED indicator light on and the printer cannot be used. Are HP printers also need reset and how to cope with blink on HP D2566?

The printer requires a reset either manually or software. This event will often be found on the Canon and Epson. As for the printer includes the HP Deskjet D2566 Printer and HP’s other types that do not require a reset, because there is no protection against the board or this HP printer cartridges. Besides the HP D2566, but it actually applies also for the HP Deskjet 3535, 3420, 3920, 2466 which had the power light blink blinking or ink continues. And it does not mean we have to reset the HP Deskjet printer. Blink on HP D2566, 3535, 3420, 3920, 2466 This is a sign that one of the HP deskjet printer cartridge chip is damaged and must be replaced with a new cartridge.

How to overcome the blink HP Deskjet D2566, 2466, 3535, 3420, 3920:
  • Suppose that you suspect is defective color cartridge. Take the black cartridge and allow only the color cartridge installed.
           pressing the button on  
  • observe the power indicator light or ink, if the HP Deskjet D2566 Printer, 3535, 3420, 3920, 2466 you still blink means the color cartridge is damaged.
  • If the power indicator light or flame full of ink, it means that your HP Deskjet printer cartridge color you are still good.
  • Take the color cartridge and reinsert the black cartridge. Means that only the black cartridge installed in the HP deskjet printer.
  • Then turn on your HP Deskjet printer.
  • Make observations on the power indicator light or ink, if the printer is HP Deskjet D2566, 3535, 3420, 3920, 2466 you still blink again means your black cartridge is damaged.
  • If the power indicator light or ink full flame, meaning a black cartridge HP DeskJet printer you are still good.
  • In conclusion,

HP Deskjet printers blink is caused by a defective cartridge is not for requesting reset. If your HP Deskjet printer cartridge is damaged, you can try cleaning the first pin in the cartridge with a pencil eraser. If it still damaged or blink, it means you already need to replace it.


Read More Add your Comment 5 comments


 

Our Partners

© 2010 Printer Repair Experts All Rights Reserved Thesis WordPress Theme Converted into Blogger Template by Hack Tutors.info